The Imenco 15Te Subsea Winch is intended for offshore subsea pulling operations by…
The Imenco 15Te Subsea Winch is intended for offshore subsea pulling operations by use of ROV.
We single-handedly carry out all testing and power calculations of all models according…
We single-handedly carry out all testing and power calculations of all models according to the relevant standards. Imenco performs engineering with complete solutions from specifications and concept to design and strength calculation. We have our premier experience in the areas of drill floor, subsea and downhole. Our skilled development department…
The Rov Tensioning Tool is easily operated by a T4. Bolt tensioning and…
The Rov Tensioning Tool is easily operated by a T4. Bolt tensioning and nut spinning performed by one tool. It can be set to pre-tension bolts from 0-1500 kN/ M28-M60 (larger dimensions on request). By use of the Imenco special design thread adapter, the risk of thread damage is eliminated.…
Hydraulic shackle lifting arrangement with underwater cameras and lights for precision placing of…
Hydraulic shackle lifting arrangement with underwater cameras and lights for precision placing of rocks, etc. on the seabed.
Interface to FMC top release guideposts without extension profile.
Interface to FMC top release guideposts without extension profile.
The Imenco Guidepost Extension GPE can be installed onto the top of 8in…
The Imenco Guidepost Extension GPE can be installed onto the top of 8in guideposts for temporary increase of the guiding length. The GPE makes it possible to use permanent short posts (to avoid them to protrude above e.g. over-trawlable subsea templates) and still obtain proper guiding through narrow roof openings…
The ROV Shackle is used for lifting operations of subsea equipment and includes…
The ROV Shackle is used for lifting operations of subsea equipment and includes a ROV operated mechanical actuator for connecting and disconnecting the shackle. Robust design based on standard certified shackle, equipped with mechanical ROV-operated «open and close» function. By using this shackle, the ROV is enabled to open and close…
The Imenco Pile Gripper Solution is a combined solution for Jacket Landing &…
The Imenco Pile Gripper Solution is a combined solution for Jacket Landing & Lock Down in one easy operation. The system is designed to lock down and stabilize a jacket during the installation and grouting phases reducing cost and risk of weather downtime. Key benefits: Fast, Diver-less & ROV friendly…
Imenco has developed and supplied dedicated 100Te WLL NC-50 Lifting Sub (NC-50 Lifting…
Imenco has developed and supplied dedicated 100Te WLL NC-50 Lifting Sub (NC-50 Lifting Adaptor/ Deployment Pup piece) for mounting on top of X-mas Tree Running Tool or other equipment. This unit connects the Running Tool to the lifting line for subsea installation and retrieval operations. The sub has a cylindrical…
X-Mas Tree emergency release device-Combines Safe Lifting and Overload Protection in one unit.…
X-Mas Tree emergency release device-Combines Safe Lifting and Overload Protection in one unit. A 100Te Combined Weak Link (CWL) has been developed and delivered by Imenco for use in the lifting line during subsea lifting operations of X-mas Trees and other subsea equipment. The CWL combines 2 operational modes: 1)…
Imenco has developed and supplied easy installable interface for connecting subsea umbilical termination…
Imenco has developed and supplied easy installable interface for connecting subsea umbilical termination on top of e.g. X-mas Tree Running Tools. This unit allows a flexible and simple connection using a standardized interface.
The Imenco S-Hook Lifting Anchor is developed with a purpose to achieve a…
The Imenco S-Hook Lifting Anchor is developed with a purpose to achieve a safe handling when steel structures e.g. riser pipes are being removed during demolition and decommissioning of offshore structures.
The GPEAR M4 model is specifically developed for installations on posts where a…
The GPEAR M4 model is specifically developed for installations on posts where a ROV will have no, or very limited, side access to the external top release sleeve.
The GP adapter acts as a centralizer extending the guiding length for most…
The GP adapter acts as a centralizer extending the guiding length for most types of guideposts. Compatible to guideposts with top receptacle for most common types of guidewire anchors.
The OE10-104 is the latest generation of pan and tilt unit OE has…
The OE10-104 is the latest generation of pan and tilt unit OE has designed and manufactured. This all-electric pan and tilt unit has been designed for positioning of cameras, lights and mechanical scanning sonar in subsea applications.
Allows for guiding of modules onto guideposts not standing vertically. Consists of an…
Allows for guiding of modules onto guideposts not standing vertically. Consists of an Imenco Slimline Anchor and a range of flexible elements over a wire. Connection to the main upper wire through a Slimline Anchor socket (Potting) Connected/disconnected as a standard Slimline Anchor Protected from overloading by shearpin in the…
A smart way to perform loadtransfere subsea or disconnect one lifting rope. An…
A smart way to perform loadtransfere subsea or disconnect one lifting rope. An element that allows for a loadtransfere from one lifting rope to another • No external power needed, all operations by ROV manipulators • Easy release subsea, by ROV • Load tested with lifting certificate. • Connecting of…
The Latch, bullet with cast in wire is designed to be used for…
The Latch, bullet with cast in wire is designed to be used for thruster replacement, performed offshore. Can be equipped with a bend restrictor from the lower threaded part to the upper bullet. Made from high strength steel The Eagle latch has a top that are to be potted to…
The Imenco Torque Tool from the Imenco Cathodic Protection Systems range of products,…
The Imenco Torque Tool from the Imenco Cathodic Protection Systems range of products, is a purpose made hydraulic torque tool for secure installation of Retrofit Anode Clamps.
The Imenco Bottom Releasable Mini Guidepost MGP-BR is a low weight small guidepost…
The Imenco Bottom Releasable Mini Guidepost MGP-BR is a low weight small guidepost used for e.g. final guiding of tools, pods or other low weight equipment. A lock/ release pin mechanism is integrated in the guidepost receptacle. The post top can adapt GWA-22’ or GWA-22’S Guidewire Anchor.
The Imenco RTR Receptacle for Top Releasable Guidepost - RTR is prepared for…
The Imenco RTR Receptacle for Top Releasable Guidepost - RTR is prepared for welding on bottom structures where Top Releasable Guideposts (GPTR/ GPAR) will be installed. The receptacle has a lead-in/ landing cone at top and a shoulder at the bottom end for locking down the guide post.
The Imenco RBR Receptacle is to be used on subsea structures for installation…
The Imenco RBR Receptacle is to be used on subsea structures for installation of Bottom Releasable Guideposts (GPBR). The receptacle for Bottom Releasable Guideposts - RBR has a robust ROV/diver operated locking pin mechanism for lock down of the post.
The MRTR Receptacle is prepared for bolting on structures where the Top Releasable…
The MRTR Receptacle is prepared for bolting on structures where the Top Releasable Mini Guidepost MGP-TR will be installed. The receptacle for Top Releasable Mini Guidepost has a lead-in/ landing cone at top and a shoulder at the bottom end for locking down the guide post.
The MRBR Receptacle is prepared for bolting on subsea structures where Bottom Releasable…
The MRBR Receptacle is prepared for bolting on subsea structures where Bottom Releasable Mini Guidepost MGP-BR shall be installed. The Receptacle for Bottom Releasable Mini Guideposts has a simple and robust ROV/diver operated locking mechanism for lock down of the post.
The Imenco guidepost top slotted is similar to the standard post top but…
The Imenco guidepost top slotted is similar to the standard post top but provided with a slot for welding to top of 8in slotted guide post (219mm OD).
The Imenco Hinged Guidepost top is for welding to top of 8in slotted…
The Imenco Hinged Guidepost top is for welding to top of 8in slotted guide post pipe (219mm OD). The Hinged Post Top allows the post slot to be opened/ closed for entering of the guide wire.
The Imenco Guidepost Top Adapter mounting on top of 8in guideposts with GL-4…
The Imenco Guidepost Top Adapter mounting on top of 8in guideposts with GL-4 post top profile. This adapter will enable use of Imenco GWA-22’/ GWA-22’S Guidewire Anchors and Guide Post Extension (GPE).
The Imenco Guidepost Extention GPE GL-4 is developed for installation on top of…
The Imenco Guidepost Extention GPE GL-4 is developed for installation on top of 8in guideposts with Regan GL-4 post top profile. This will provide extension of the guidepost and also allow the use of Imenco Guidewire Anchors. The GPE GL-4 can be handled by the guideline and easily be installed…
The Imenco Top Releasable Mini Guidepost MGP-TR is a small low weight guidepost…
The Imenco Top Releasable Mini Guidepost MGP-TR is a small low weight guidepost used on structures for lead-in and final guiding of smaller tools, pods or other small equipment where guidewires are not to be used. The MGP-TR has a very low weight for handling and installation/ retrieval by ROV.…
The Imenco Anchor Releasable Guidepost GPAR can be used on subsea structures where…
The Imenco Anchor Releasable Guidepost GPAR can be used on subsea structures where there is only access to the post from above. Can be easily installed and retrieved using the Extended Guidewire Anchor or Extended Lifting Anchor. The GPAR can be provided with Post Top profile to fit Guidepost Extensions…
The Imenco Bottom Releasable Guidepost GPBR can be used on subsea structures where…
The Imenco Bottom Releasable Guidepost GPBR can be used on subsea structures where there is access to the Post Receptacle at the bottom end of the post. The locking/ release mechanism is integrated in the guidepost receptacle. The GPAR can be provided with Post Top profile to fit Guidepost Extensions…
The Imenco Guidepost Extension GPE can be installed onto the top of 8in…
The Imenco Guidepost Extension GPE can be installed onto the top of 8in guideposts for temporary increase of the guiding length. The GPE makes it possible to use permanent short posts (to avoid them to protrude above e.g. over-trawlable subsea templates) and still obtain proper guiding through narrow roof openings…
The Imenco Top Releaseable Guidepost GPTR can be used on subsea structures where…
The Imenco Top Releaseable Guidepost GPTR can be used on subsea structures where there is side access for ROV at upper part of the post. Can be easily installed and retrieved using Guidewire Anchor or Lifting Anchor. The GPTR is available at different lengths, diameters and strength classes.
The Imenco GPE Profiled Guidepost Top has the standard Imenco GPE profile to…
The Imenco GPE Profiled Guidepost Top has the standard Imenco GPE profile to enable installation of Guide Post Extension onto the top of the post. The Guidepost Tops w/ GPE profile is prepared for welding to 8in nom. pipe diameter (219mm OD).
Imenco has developed different frames for various use. Guide frames can be delivered with…
Imenco has developed different frames for various use. Guide frames can be delivered with latching system, enabling to lift several frames from bottom to surface by lifting the top frame. Please contact us with your requirements.
Improve the safety and handling of your expensive equipment and valuable personnel. Imenco…
Improve the safety and handling of your expensive equipment and valuable personnel. Imenco ROV latches will increase overall safety and ease deployment and recovery of small to medium sized ROV’s. The lock-latch enables easy attachment/detachment to the cable using it’s unique cable entrance door solution. General description: The Imenco ROV…
For all situations where a controlled emergency release point is required, the Imenco…
For all situations where a controlled emergency release point is required, the Imenco Snapper™ Weak Link range provides the perfect solution in ensuring a high safety standard for your lifting operations.
The Imenco Stinger ROV Drilling Tool is a portable hydraulically operated drilling machine…
The Imenco Stinger ROV Drilling Tool is a portable hydraulically operated drilling machine which can be operated by a work class ROV. It is designed for subsea drilling operations on a variety of applications and steel thicknesses.
Imenco compensators are made from polycarbonate tubing, aluminium flanges and stainless steel springs.…
Imenco compensators are made from polycarbonate tubing, aluminium flanges and stainless steel springs. They are prepared for installation of optional warning compensation volume sensors. Subcon proximity sensors are normally used. Hydraulic connection(s) are done on top with two JIC 1/2” fittings. All nuts and bolts/rods are stainless steel.
Imenco has over the 10 past years delivered a range of subsea cutters…
Imenco has over the 10 past years delivered a range of subsea cutters for different subsea removal projects. • Chain cutting • Pipe cutting • Bolt cutting • Other structures
The Imenco ROV Operated Shackle is a semi-automatic shackle with an easy-to use…
The Imenco ROV Operated Shackle is a semi-automatic shackle with an easy-to use positive, double locking system which ensures safe lifting operations. Due to its smart design and the high quality, the Imenco ROV Shackle is established as the industry standard for ROV Shackles globally. Download the Imenco ROV Shackle Brochure…
The Imenco 3 finger manipulator front adapter is made in high strength stainless…
The Imenco 3 finger manipulator front adapter is made in high strength stainless steel and will make an exact fit to Schilling’s Titan II/III/IV and Orion manipulators. The front adapter assembly comes complete with actuation plate and piston and all necessary gaskets and will replace the standard parallel grip by…
The Imenco 4-finger front adapter is made in high strength stainless steel and…
The Imenco 4-finger front adapter is made in high strength stainless steel and will make an exact fit to Schilling’s Titan II/III/IV and Orion manipulators. It is perfect to use on T-bar grips and for other applications that require a steady grip. The front adapter assembly comes complete with actuation…
The Imenco Standard Guidewire Anchors are recognized by their slender bodies and wider…
The Imenco Standard Guidewire Anchors are recognized by their slender bodies and wider heads. This gives each Imenco Standard Guidewire Anchor a shoulder for resting on the top of the guidepost or receptacle.
The Imenco Guidewire Anchors (or Latches) have been manufactured and used since the…
The Imenco Guidewire Anchors (or Latches) have been manufactured and used since the mid 1980s and are known in the subsea market for their ease of use and dependability. The Imenco Slimline Guidewire Anchors are easily installed and released by ROV or diver. The Imenco Slimline Guidewire Anchors are built from high strength…
The Imenco Lifting Anchors (or Latches) have been manufactured and used since the…
The Imenco Lifting Anchors (or Latches) have been manufactured and used since the late 1990s and are known in the subsea market for their ease of use and dependability for safe lifting operations. The Imenco Lifting Anchors are easily installed and released by ROV or diver. The Imenco Lifting Anchors…
Imenco supplies a specially designed Load Transfer Hook for retrieval and transferal of…
Imenco supplies a specially designed Load Transfer Hook for retrieval and transferal of the rider form a standard ROV support vessel to the FPSO/floater. Maintaining full integrity and security of the load, the hook also provides features for secondary load transfer back to the support vessel if any of the…
The Lifting hooks are delivered for loads from 85 – 400Te WLL The…
The Lifting hooks are delivered for loads from 85 – 400Te WLL The Lifting hooks have a safety arrangement which can be fixed in open or in closed position, and easily operated by a work class ROV.